IMPORTANT
As a reminder, if there is no information on the update, it is because it concerns only the update of documentation, translation or text
Ajout du produit Dragino CPL03-LB/LS - LoRaWAN Outdoor Open/Closed Dry Contact Sensor
Ajout du produit Dragino LHT52 - LoRaWAN Indoor Temperature and Humidity Sensor
Decoder correction Vega
Ajout des commandes Dragino CPL03-LB/LS - LoRaWAN Outdoor Open/Closed Dry Contact Sensor
Mise à jour décodeur et encodeur Thermokon 835633 - NOVOS 3 Room control module temperature, relative humidity, CO2
Ajout du produit BMeters IWM-LR3 - Water Meter Reader
Correction downlink du Vega SI-11
Ajout du produit Milesight EM300MCS - Magnetic Contact Switch
Correction du choix du broker local lors de la génération automatique
Ajout du produit Milesight CT303 - Smart Current Transformer CT303
Ajout du produit Nexelec ATMO / SENSE / AERO / PMT / AERO Lora
Ajout du produit Nexelec LoRa Air Sensors (Sign, Rise, Feel, Move, Wav, View)
Ajout du produit **
Correction du décodeur WoMaster LR144
Correction du décodeur Adeunis ARF8230ABA - Pulse meter pulse transmitter
Ajout du produit Eastron Smart Energy Meter SDM-530
Ajout des generic types au produit Milesight Smart Radiator Thermostat WT101
Ajout du produit Eastron Smart Energy Meter SDM-230
Decoder correction NKE Batch
Regenerating equipment in Chirpstack with the “Regenerate LoRaWAN configuration” button”
Gestion du fPort dans le décodage
Dragino LHT65 ajout du Set Transmit Interval
Dragino RS485-LN + NILAN correction du décodeur
NKE Fil Pilot correction du Device Profile en classe C
Suppression des équipements MQTT et Chirpstack suite à la suppression de l’équipement Lorapayload
Vérification de la taille des DevEUI et AppKey avant la génération automatique
Adding configuration Milesight WS203
Ajout des commandes de downlink pour Dragino LT-22222
Adding configuration WoMaster LR144
Ajout des commandes de downlink pour Dragino LHT-65 (Envoie des uplinks en confirmed)
Ajout de la commande info “Downlink acknowledged”
Ajout du bouton copier du Deveui et Appkey
Ajout des commandes de downlink pour Dragino LT-22222
Mise à jour du décodeur Ewattch Squid Pro Rogowski
Ajout du produit MClimate - 16A Switch & Power Meter LoRaWAN
Ajout de la possibilité d’envoyer deux downlinks dans la même commande Action
Ajout du produit Dragino T68DL - Temperature Sensor
Ajout du produit Milesight TS201 - Temperature Sensor
Ajout du produit Milesight TS30x - Temperature Sensor
Ajout du produit Watteco In’O
Ajout du produit Milesight UC100 - IoT Controller
Ajout du produit Milesight UC300 - IoT Controller
Ajout du champ Remarque pour les modules
Correction du Device Profile Power-Adapt Power-Elec 6
Correction des commandes de downlink + uplink de Quantify Cubic Meter
Correction du décodeur Dragino RS485-LN + NILAN
Correction du décodeur Quantify Cubic Meter
Adding configuration NKE Torano
Changing the configuration Dragino LSN50 V2 - MOD4 (properties : Digital Interrupt)
Adding configuration Thermokon 798808 - MCS Ambient sensor temperature, relative humidity, brightness
Adding configuration Thermokon 817318 - MCS Motion detector, Room sensor temperature, relative humidity, brightness, movement, presence, status
Adding configuration Thermokon 824248 - NOVOS 3 Room control module temperature, relative humidity, CO2
Adding configuration Dragino RS485-LN + NILAN
Added Chirpstack panel
Added “Regenerate LoRaWAN configuration” button”
Adding configuration Milesight Ambience Monitoring Sensors AM102
Adding configuration Electronic Card - TIC LoRaWAN
Fix downlink command Milesight Smart Radiator Thermostat WT101
Changing the configuration Ewattch Squid Pro Rogowski
Decoder correction MClimate Wireless Thermostat
Added info commands for Ewattch Squid Pro Rogowski
Added Battery for NKE Torano
Adding configuration Thermokon 835633 - NOVOS 3 Room control module temperature, relative humidity, CO2
Adding configuration Adeunis ARF8230ABA - Pulse meter pulse transmitter
Changing the configuration MClimate Wireless Thermostat (properties : Manual Target Temperature Update)
Adding configuration Milesight WS303 (properties : Battery, Leakage Status)
Changing the configuration Vega SI-11 Rev2 (properties : Communication period, Input Mode)
Adding configuration MClimate Fan Coil Thermostat
Adding configuration WATTECO NETW’O network tester
Adding configuration Milesight EM300 DI
Adding configuration Mclimate Display CO2 lite
Adding configuration Mclimate Display CO2
Adding configuration Milesight Smart Fan Coil WT301
Adding configuration Thermokon 798228 - MCS Motion detector, Room sensor temperature, relative humidity, movement, presence
Changing the configuration SHE MIO LORA V2 (add up to 20 temperature probes)
Adding configuration Enginko MCF - LW13 IO
Added downlinks commands Quantify Cubic Meter
Adding configuration Thermokon 798808 - MCS Ambient sensor temperature, relative humidity, brightness
Adding configuration Ewattch Squid Pro Rogowski
Added downlink commands from Thermokon 811187 - NOVOS 3 Room sensor temperature, relative humidity
Adding configuration Milesight - Smart Current Transformer CT101
Adding configuration Dragino - RS485-LN + CarloGavazzi EM540
Adding configuration Dragino - RS485-LN + OTMetric + Polier
Added downlink commands from MClimate Wireless Thermostat
Adding configuration Milesight Smart Radiator Thermostat WT101
Adding configuration Dragino D23LBLS (properties : Battery, Temp-White, Temp-Red, Temp-Black, Alarm, PA8 Level, Mode)
Adding configuration Citylone SL32 and Citylone SL22 (properties : Voltage, Current, Power, Cos Phi, Temperature, LED Voltage, Lamps level, Lamps mode, Request Position, Latitude, Longitude, Request Time Change State, Enable Time Change, Disable Time Change, RSSI, Timestamp, Update via LNS, On Relay , Off Relay)
Adding configuration Quantify Cubic Meter (properties : Error Code, Total Volume, Leak Status, Battery Status, Minimum Temp, Maximum Temp, Ambient Temp)
Adding configuration Eastron SDM630 (properties : Serial Number, Total Energy, Frequency, Total Power Factor, Maximum Total System Power Demand, Total Current)
Adding configuration Dragino CS01 LB (properties : Battery, EXTI_Trigger, EXTI_Level, Current1, Current2, Current3, Current4, CurL_status, CurH_status)
Adding configuration Enerbee e-VAV (properties : Temperature, Humidity, Target flow, Current flow, CO2, IAQ, Charge level, Damper opening level, System status)
Adding configuration Milesight EM300TH (properties : Battery, Temperature, Humidity)
Adding configuration NKE Triphas’O (properties : Voltage Phase (A, B, C), Current Phase (A, B, C), Angle Voltage Current Phase (A, B, C), Positive Active Energy Phase (ABC, A, B, C), Negative Active Energy Phase (ABC, A, B, C), Positive Reactive Energy Phase (ABC, A, B, C), Positive Active Power Phase (ABC, A, B, C), Negative Active Power Phase (ABC, A, B, C) ), Positive Reactive Power Phase (ABC, A, B, C), Negative Reactive Power Phase (ABC, A, B, C), Binary Input State Phase (ABC, A, B, C))
Adding configuration Thermokon Temp RH (properties : Temperature, Humidity)
Adding configuration Milesight EM300TH (properties : Battery, Temperature, Humidity)
Adding configuration Milesight EM500LGT (properties : Battery, Illumination)
Changing the log level for certain information generated by the plugin
Changing the module type Milesight EM500 PT100
Adding configuration Dragino D20-LB (properties : Battery, Temperature Red, Alarm, PA8 Level, MOD)
Adding configuration RAK c15003 (properties : Temperature, Humidity, Pressure, Temperature2)
Changing the configuration Mclimate Vicki (properties : GetKeepAlive, KeepAlive, GetDevicePrimaryOperationalMode, DevicePrimaryOperationalMode, GetOperationalMode, OperationalMode, Proportional control, Equal directional control, Proportional Integral control, GetControlAlgorithm, ControlAlgorithm, Open window detection parameters (1.0 accuracy), Open window detection parameters (0.1 accuracy))
Adding the column State to display the value of the info orders
Adding configuration Citylone SmartLighting-Box 2 (properties : stateS1, stateS2, stateS3, stateS4, statusS1, statusS2, statusS3, statusS4, input1, input2, Off Output 1 fixed, On Output 1 fixed, Auto Output 1 fixed, Off Output 2 fixed, On Output 2 fixed, Auto Output 2 fixed, Off Output 3 fixed, On Output 3 fixed, Auto Output 3, Off Output 4 fixed, On Output 4 fixed, Auto Output 4 fixed, Off All fixed, On All fixed, Auto All fixed, DureeOnS1, DureeOnS2, DureeOnS3, DureeOnS4, DureeOffS1 , DureeOffS2, DureeOffS3, DureeOffS4, RSSI, Timestamp GMT, Timestamp Local, Update via LNS, Longitude, Latitude, Index Base, HCHC Index, HCHP Index, TIC Meter ID, Tariff option, Single-phase Instantaneous Current, Phase1 Instantaneous Current, Phase2 Instantaneous Current , Instantaneous Current Phase3, Max Instantaneous Current Single Phase, Max Instantaneous Current Phase1, Max Instantaneous Current Phase2, Max Instantaneous Current Phase3, Max Active Power, Thresold Alarm Power, Apparent Instantaneous Power, Power Failure, Time Change State)
Adding configuration RAK2171 (properties : Message ID, Application ID, Device ID, Battery, Timestamp, GPS Fix Status, Payload Type, Longitude, Latitude, Accuracy, GPS Start Number, SOS, Alarm Level)
Adding configuration Milesight WS50x (properties : Version, Voltage, Activate Power, Active Factor, Power Consumption, Current, Switch 1, Switch 2, Switch 3)
Adding configuration Milesight WS51x (properties : Version, Voltage, Activate Power, Active Factor, Power Consumption, Current, State)
Changing the configuration SHE MIO LORA V2 (properties : ON 1-2, OFF 1-2, ON 1-3, OFF 1-3…)
