Nodon Switch - Wall Switch
The module
The Jeedom visual
Summary
The NodOn® wall switch can directly control any Z-Wave® or Z-Wave Plus® compatible device such as the NodOn® smart plug or even trigger scenes via a compatible home automation system.
The switch has a mounting plate for easy mounting in the house: using the screws of a mounting pot, by screwing it to the wall, or simply by sticking it via the double-sided adhesives present on the back of the plate.
Fonctions
- Control alone or with a home automation system
- Easy to assemble and disassemble
- Pleasant feeling of support
- Wireless
- 2 years of battery
Technical characteristics
- Food : CR2032 battery - Autonomy 1,5 - 2 years
- 4 buttons
- Wall mounting by double-sided adhesive (included) or screws (not included))
- Operating temperature : 0 ° C to 40 ° C
- Altitude : 2000m
- Z-Wave® radio protocol : 868.4MHz - 500 Series - Compatible Z-Wave Plus® SDK 06.51.06
- Scope : 40m indoors / 70m outdoors
- Dimensions : 80 *80 *15mm
- 2 years warranty
- EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013
- EN 300 220-2 V2.4.1
- EN301 489-1 V1.9.2
- EN301 489-3 V1.6.1
- EN 62479:2010
Module data
- Mark : Nodon
- Name : CWS-3-1-01 Wall Switch
- Manufacturer ID : 357
- Product Type : 2
- Product ID : 3
Configuration
To configure the OpenZwave plugin and know how to put Jeedom in inclusion, refer to this Documentation.
IMPORTANT
To put this module in inclusion mode, press the two buttons (1 and 2) until the light turns pink, then press button 1, in accordance with its paper documentation.
Once included you should get this :
Commandes
Once the module is recognized, the commands associated with the modules will be available.
Here is the list of commands :
-
Buttons : it is the command which will push the button up
- —————- + —————- + ————— - + —————- + —————- + | Buttons | Support | Long press | Relaxation | Double support |
- ================ + ================ + ================ = + ================ + ================= + | 1 | 10 | 12 | 11 | 13 |
- —————- + —————- + ————— - + —————- + —————- + | 2 | 20 | 22 | 21 | 23 |
- —————- + —————- + ————— - + —————- + —————- + | 3 | 30 | 32 | 31 | 33 |
- —————- + —————- + ————— - + —————- + —————- + | 4 | 40 | 42 | 41 | 43 |
- —————- + —————- + ————— - + —————- + —————- +
Configuration of the module
IMPORTANT
During a first inclusion always wake up the module just after the inclusion.
Then if you want to configure the module according to your installation, you have to go through the “Configuration” button of Jeedom’s OpenZwave plugin.
You will arrive on this page (after clicking on the parameters tab)
Parameter details :
- 1-2 : Allows you to choose the profile of the buttons when used centrally (useless for use in Jeedom)
- 3 : Important parameter to say if the switch should operate in Scene or Central Scene mode (Absolutely set Scene)
- 4-7 : Choose the button operating mode (in case of group associations)
- 8 : Allows you to choose the operating mode of the LED
Groupes
This module has 7 association groups.
- Group 1 - Lifeline : This group is generally used to report information from the Smart Plug to the main network controller.
- Group 2 to 5 - The devices in these groups are controlled by the corresponding button according to the MONO profile
- Group 6 to 7 - The devices in these groups are controlled by the corresponding button according to the DUO profile
IMPORTANT
At least Jeedom should end up in group 1
Good to know
Specificities
- This module can be finicky on inclusion. Do not hesitate to wake it up 1 or 2 times after inclusion. Well check the association group.
Wakeup
To wake up this module just press one of these buttons
Important note
IMPORTANT
You have to wake up the module : after its inclusion, after a change in configuration, after a change in wakeup, after a change in association groups
